Wood Panel Edge Bander

Wood Panel Edge Bander

TT-306DSPTF is the TT-306DSP frame with two end-cut motors, one per trimming head, and a flat scraping station after the fine trim: the build for edges that will be seen, painted or handled. Pre-milling, 8 m/min feed, 10 to 45 mm panels, 0.4 to 2 mm tape.
Send Inquiry
Functions

TingTing Woodworking Machinery Co., Ltd. is one of the leading manufacturers and suppliers of wood panel edge bander in China. As we have world-leading production equipment and strong manufacturing capabilities, we warmly welcome you to buy premium wood panel edge bander from our factory. For price consultation, contact us.

 

A wood panel edge bander is judged on two things a buyer can see in the sample drawer: whether the ends are square and flush, and whether the band reads flat under a raking light. The TT-306DSPTF is the TT-306DSP frame with both of those points reworked: two end-cut motors instead of one, and a flat scraping station after the fine trim.

Everything else is the DSP the workshops already know, from the PCD pre-mill to the 120 x 80 mm minimum part. The TF is that machine with a different finishing end.

TT-306DSPTF wood panel edge bander, front view with the hood closed

TT-306DSPTF with the hood closed: two extraction pipes along the top, control panel at the outfeed end, 2,580 mm of frame on two levelling feet.

TT-306DSPTF at a glance

The DSP numbers, with the end-cut station doubled.

8

 

m/min feed

2

 

end-cut motors

120

 

mm min length

45

 

mm panel gauge

What the TF adds to the DSP

Two changes, both at the finishing end. Neither is visible from the outside of a cabinet, and both are visible on the first part you pick up.

Two upgrades, one frame

Everything not listed here is carried over from TT-306DSP without change.

Two end-cut motors

One 0.37 kW, 12,000 rpm motor behind each trimming head, so each end of the panel is set on its own reference instead of on a shared linkage.

A flat scraping unit

A scraping station after the fine trim takes the cutter marks off the band, leaving a flat matte edge rather than a machined sheen.

The DSP underneath

Pre-mill, glue and tape cut, fine trim, polish: the same station list as the DSP, in the same order on the frame.

Two end-cut motors, one per end

A single-motor end trimmer drives both heads from one unit through a mechanical link. The link is why two ends disagree: adjust one head and the other follows, so every setting is a compromise between the two ends of the part. The TF takes the link out and puts a motor behind each head.

Where that shows up is setup, not the sample. Each end is trimmed, checked and left alone, with nothing between motor and cutter to wear, so a setting made at the start of a shift holds to the end of it. On the 120 mm part this wood panel edge bander accepts, the two heads work within a few centimetres of each other, and that is exactly where a shared setting leaves a visible step.

Edge bander hood open, all stations visible in line
Edge bander from the left three-quarter with the hood open

Hood up, front and three-quarter. The trimming heads at one end of the frame each carry their own motor and their own dust hose. The glue station, the hold-down rollers and the pre-mill in front of them are the TT-306DSP parts.

Flat scraping, after the fine trim

Fine trimming leaves a machined band: two cutters, one from each face, meeting in the middle of the edge. It is square, and it is also glossy, with a fine witness line where the two passes meet. On PVC and ABS that line is what a customer runs a thumb along.

The scraping station follows with a flat blade set just under the band surface, shaving the high spots and the line with them. What comes out is a matte, flat edge: the finish that takes paint, lacquer or laminate trim without telegraphing the band underneath. On 0.4 mm tape that is a cosmetic gain; on 2 mm PVC it is the difference between an edge that looks machined and one that looks finished.

Left three-quarter view of the panel edge bander
Right three-quarter view with the control panel and outfeed

Left and right three-quarter, hood closed. In build order the scraper sits between the fine trim and the polishing wheel; the control panel sits at the outfeed end, at the operator's eye level.

Technical data

TT-306DSPTF specifications

This wood panel edge bander carries the TT-306DSP figures; the two rows marked TF are what changes.

Model TT-306DSPTF
Shortest part 120 mm
Narrowest part 80 mm
Panel gauge 10 to 45 mm
Tape gauge 0.4 to 2 mm
Feed rate 8 m/min
Pre-mill drive 2 x 1.1 kW, 12,000 rpm
End trim drives (TF) 2 x 0.37 kW, 12,000 rpm (DSP: 1 x 0.37 kW)
Fine trim drives 2 x 0.35 kW, 12,000 rpm
Scraper (TF) Flat blade, after the fine trim
Connected load 6.23 kW (5.86 kW DSP + the second trim motor)
Air supply 0.5 MPa
Supply 380 V, 50 Hz (optional)
Footprint 2,580 x 585 x 1,410 mm
Weight, net 660 kg

The 6.23 kW is the DSP's 5.86 kW plus one 0.37 kW motor; no other unit in the build changed. Length and weight are the DSP figures, because the TF uses the same frame: the scraper adds a station to it, and the final overall length is confirmed on the general-arrangement drawing at order.

What it needs on the floor

At 2,580 mm long, 585 mm wide and 660 kg this wood panel edge bander is a bench machine, not a line. It fits a 6 m bay with room to feed a 2,440 mm panel, and the outfeed needs the same clearance again so the part clears the polishing wheel. Air at 0.5 MPa, 380 V three-phase, extraction from the pipes on top of the hood.

Three-quarter view with the hood closed and the dust pipes on top
Front view of the machine with the hood closed

The same machine from two more angles. The white pipe run across the top of the hood is the extraction line: it is the one part of the installation that has to be planned before the machine is moved into place.

DSP, DSPTF, or another frame

The TF is the right build when the banded edge is the visible face of the product: painted kitchen fronts, 2 mm PVC on exposed cabinet sides, shelf edges a customer handles. Where the edge is hidden and volume is the problem, the plain DSP does the same work for less money. Where the bottleneck is the small part rather than the finish, the dual-motor automatic panel edge bander is the closer match, and the straight edge banding machine page covers the DBP build for workshops that need pre-milling in the smallest footprint.

The paint test is the one to run before deciding. Band a scrap of the board you actually use, at the tape thickness you actually buy, then put a coat of primer on it and look along the edge under a window. A gloss band with a witness line in the middle will telegraph through two coats; a scraped one will not. That test costs an hour and settles whether the second motor and the scraper are worth their place on the invoice.

FAQ

Q: What is different between TT-306DSP and TT-306DSPTF?

A: Two things: two end-cut motors, one per trimming head, instead of one driving both through a link; and a flat scraping unit after the fine trim. Frame, feed speed, pre-milling and tape range are unchanged.

Q: What does flat scraping actually do?

A: It shaves the fine witness line that the two fine-trimming cutters leave where they meet, and takes the sheen off the band. The edge comes out flat and matte, which is what paint, lacquer and laminate trim need to sit on without showing the band underneath.

Q: What panel and tape sizes does this wood panel edge bander take?

A: Panels from 120 mm long and 80 mm wide, 10 to 45 mm thick, with edge band from 0.4 to 2 mm at 8 m/min feed.

Q: Does the second end-cut motor change the power supply?

A: It moves connected power from 5.86 kW to 6.23 kW. Supply stays 380 V three-phase at 50 Hz, with air at 0.5 MPa.

Q: Is the length still 2,580 mm with the scraper added?

A: The frame is the DSP frame and 2,580 x 585 x 1,410 mm is the published figure for it. The scraper adds one station, so the overall length on the drawing you receive at order is the number to lay out against.

Send a sample edge, get a build sheet

Tell us the tape you run, the panel thickness and the finish the edge has to take, and we will come back with the station list for this wood panel edge bander and the drawing for your floor.

Request a quote

Hot Tags: wood panel edge bander, panel edge bander, edge bander for wood panels, wood panel edge banding machine, automatic edge bander for laminated panels, automatic edge bander for MDF, automatic edge banding machine for cabinet production, automatic edge banding machine for wood panels, automatic edge banding machine with automatic feeding, one sided edge bander

Send Inquiry
Send Inquiry